Guides
Know-how from people who run the equipment
Practical guidance on operating acetylene plants, handling cylinders and choosing grades — written from operating experience rather than from a brochure, with a named author and a review date on every page.
- 169
- Guides published
- 1947
- Operating since
- BIS
- Technically reviewed
Acetylene: the gas and its data16
What acetylene is, its properties, solvents, grades and uses.
Also: Acetylene safety data sheet (SDS / MSDS) · The acetylene standards: IS 308, IS 7312:2018, IS 14814 · Everything KIGL publishes on acetylene
- Acetylene technical data sheet physical properties with their primary sources and the conditions they were measured at
- Acetylene gas formula, structure and properties the numbers behind the hottest flame in the workshop
- Is acetylene lighter than air? What a specific gravity of 0.906 means for ventilation and leak detection
- Acetylene flammability limits and ignition temperature 2.5–82 % in air, 305 °C, and why the upper limit is really 100 %
- Acetylene's critical temperature is 35.18 °C what that means for a cylinder standing in an Indian summer
- Acetylene vapour pressure why it would take about 43 bar to liquefy at 20 °C, and why liquid acetylene is never used
- One number, two consequences how acetylene's +226.9 kJ/mol heat of formation gives the hottest fuel-gas flame and makes the gas decomposable
- Why acetylene is dissolved in acetone, and what the porous mass does
- Acetylene solubility in acetone why the 300 volumes figure is a Henry's-law shortcut and what was actually measured
- How much acetylene dissolves in water and in carbide sludge and how it comes back out in the pit
- Acetone versus DMF as the solvent in an acetylene cylinder capacity, carry-over, water sensitivity and why UHP grades use DMF
- Acetylene hydrate the ice-like solid that forms in wet acetylene under pressure, above freezing point
- Choosing an acetylene grade industrial, high purity and ultra high purity
- What acetylene is used for, and why nothing else does the same job
- Acetylene or LPG for cutting where each one actually wins
- Buying acetylene what to check before accepting the cylinder
Acetylene safety and decomposition13
Why acetylene can explode without air, and the rules that follow from it.
- Where the 1.5 bar acetylene pressure rule comes from and what it does not mean
- Acetylene decomposition why it can explode with no oxygen present
- Acetylene pipe diameter and detonation why the smallest pipe that will do the job is the safest one
- Dead legs in acetylene pipework why a closed pipe just longer than the predetonation distance is the worst geometry
- Why wet acetylene is safer than dry acetylene and where the hazard rises in a DA plant
- Why nitrogen dilution does not make compressed acetylene safe and what nitrogen is really for
- How rust, dust and pipe scale lower the temperature at which acetylene decomposes
- Static electricity and acetylene from 10.5 joules at 2 atm to 0.56 millijoules at 15 atm
- Copper and acetylene why the limit is 70 %, why some standards say 65, and why IS 14814 bans brass outright
- Silver solder and acetylene silver acetylide, the absolute prohibition, and what the brazing rules actually allow
- Acetylene leak detection why the smell arrives before the hazard, how to find a leak without a flame, and what to do next
- An acetylene cylinder on fire what to do, what never to do, and why
- Writing an emergency response plan for an acetylene plant stop the gas, vent the high-pressure side, deal with hot cylinders, and inspect before restart
Flashback arrestors14
How they stop a flame, choosing, fitting, testing and replacing them.
Also: KIGL flashback arrestors · IS 11006 and ISO 5175-1
- How a flashback arrestor works quenching, sintered and wet elements, and the valves that back them up
- What causes a flashback, and what a flashback arrestor actually does
- Backfire, sustained backfire and flashback what each one is, what causes it, and what to close first
- Flame arrestor or flashback arrestor two devices, two jobs, two standards
- Non-return valve or flashback arrestor? Why an acetylene system needs both, and where each one goes
- Choosing a flashback arrestor position, gas, pressure rating, flow capacity and the right standard
- Flashback arrestor pressure drop and flow capacity how IS 11006 rates flow, and why fine elements cost pressure
- Flashback arrestor installation mistakes ten errors that leave a gas line unprotected, and how to avoid them
- Testing and replacing flashback arrestors the IS 11006 type tests, annual checks and when a device is spent
- Oil, grease and flashback arrestor elements why a contaminated element quenches less, and how to keep it clean
- The twenty-minute delay why an acetylene arrestor that seems to have worked can still fail
- Wet flashback arrestors how a hydraulic seal stops a flame, and how to keep the water level that makes it work
- Bursting discs vs flashback arrestors why a relief disc cannot stop an acetylene detonation
- Packed-tower flashback arrestors for large acetylene pipelines Raschig rings, gas velocity, packed height and the upstream bursting disc
Dissolved acetylene cylinders16
What is inside, how to draw from them, store, move and inspect them.
- Inside a dissolved acetylene cylinder porous mass, acetone and the numbers that make it safe
- Acetylene cylinder sizes in India why they are measured in litres of water, not cubic metres of gas
- Handling and storing acetylene cylinders the rules that matter
- The one-seventh rule how fast acetylene can be drawn from a cylinder, and why
- Why the pressure gauge does not show how much acetylene is in the cylinder
- How to check how much acetylene is in a cylinder tare, gross weight and the 0.91 m³/kg conversion
- Acetone carry-over why an acetylene cylinder should never be run below 2 bar
- Why acetylene cylinders must be used and stored upright, and how long to wait after one has been lying down
- Storing acetylene cylinders in India what the Gas Cylinders Rules 2016 and IS 14814 actually require
- Transporting acetylene cylinders safely the Schedule VI rules, valve caps, securement and why open vehicles are compulsory
- Why an acetylene cylinder delivers less gas in cold weather, and what to do about it without a flame
- Acetylene cylinder manifolds and bulk supply non-return valves, arrestors, draw limits and sizing
- Acetylene cylinder valves and spindle keys under IS 3224:2021 outlet, materials and the rules for opening and closing
- Fusible plugs on acetylene cylinders the 98–104 °C alloy, what it protects against and what it cannot do
- Inspecting a dissolved acetylene cylinder at filling under IS 16271:2014 before, during and after the charge
- Periodic inspection of dissolved acetylene cylinders under IS 8433:2017 what is checked, when, and what condemns a cylinder
Welding and cutting7
Oxy-fuel equipment, pressures, flames and the daily checks.
- Welding gases explained the right gas for oxy-fuel, TIG, MIG, MAG, plasma and laser work, and what the ISO 14175 codes mean
- Oxy-acetylene welding and cutting the equipment, the three flames and the settings
- Oxy-acetylene regulators and working pressures the acetylene ceiling, oxygen settings by job, and how a regulator fails
- Oxy-acetylene hoses colour codes, left-hand fuel threads, clamps, and when a hose must be scrapped
- Neutral, carburising and oxidising flames, and choosing a cutting tip by plate thickness and oxygen purity
- The oxy-fuel gas daily safety checklist before the first light, during work, at every stop, and the fire watch afterwards
- Choosing a shielding gas argon, carbon dioxide or a mixture
Running an acetylene plant19
Operation, maintenance, troubleshooting and training, from the plant manuals.
Also: KIGL acetylene gas plants · Acetylene purification system
- Operating and maintaining an acetylene gas plant a practical guide
- Troubleshooting a carbide-to-water acetylene plant reading the symptom back to its cause
- The acetylene plant maintenance checklist 63 tasks, hourly to yearly, from the people who build the plant
- The acetylene plant maintenance calendar 10 daily, 18 weekly, 15 monthly and 20 yearly tasks, grouped by system
- The acetylene plant shift log what is recorded every hour, what each reading should show, and why yield per kg is the number to watch
- How acetylene is made carbide, water, and the nine stages between the carbide hopper and the cylinder
- Sizing an acetylene plant against real demand, not peak demand
- How much water per kilogram of carbide does an acetylene generator need, and why 6 to 8 litres
- Regenerating an acetylene purifier the 72-hour air cycle, the 45 °C stop and when a bed is finished
- The silver nitrate test for phosphine in acetylene sensitivity, interferences and the silver acetylide hazard
- Running an acetylene compressor suction limits, stage pressures, cooling, and why the oil turns grey
- Acetylene compressor troubleshooting, symptom by symptom
- Drying acetylene for cylinder filling calcium chloride driers, condensate drains and the empty-space rule
- Starting, stopping and purging an acetylene plant getting the air out and keeping it out
- Interlocks and alarms on a carbide-to-water acetylene plant what trips, why it fails safe, and how to prove it works
- Maintenance and hot work in an acetylene plant stop, purge, repair, purge again
- Laying out an acetylene plant in India PESO distances, single-storey compressor house, outward doors, light roof, ventilation, lighting and sludge pits
- What an acetylene plant operator must know a training syllabus covering properties, hazards, safety devices, interlocks, the shift log, purging and the first few minutes of an emergency
- Acetylene plant waste every stream from a carbide-to-water plant, how much there is, what makes it hazardous and where it must go
Calcium carbide and carbide lime13
Grades, yield, storage, impurities and what to do with the lime.
- What is calcium carbide? CaC₂ explained how it is made from lime and coke, its properties, IS 1040 grades, gas yield and uses
- Calcium carbide grades, sizes and gas yield what 300 litres per kilogram actually means
- Testing calcium carbide on delivery sampling, sieve analysis, gas yield and when to reject a lot
- Why acetylene yield per kg of carbide falls, and where the gas is going
- Calcium carbide storage why an open drum can lose 20–40 % of its gas in two days
- Calcium carbide safety data the one hazard, the heat it releases and what to do about a carbide fire
- Phosphine in acetylene why Indian carbide carries three to six times the purifier duty
- Acetylene generator overheating how polymerisation and incandescent carbide start, and how to stop them
- Carbide lime sludge how much there is, what it still holds, and how to handle and dispose of it safely
- Uses of carbide lime which outlets are proven, which are possible, and which do not work
- Calcium carbide rules in India who regulates carbide storage, generation and transport, and what each instrument covers
- Calcium hydroxide data sheet for carbide lime Ca(OH)₂ properties, solubility, pH, decomposition, hazards and storage
- Calcium carbide and fruit ripening what the FSSAI ban says, why technical carbide is unsafe near food, and the ethylene alternative
Standards, licences and regulation9
IS standards, PESO licensing and the Gas Cylinders Rules, explained.
Also: All standards pages
- How to get a PESO licence for an acetylene plant in India the Form C, E and F sequence explained
- What the Gas Cylinders Rules 2016 require of a gas filler and a cylinder user licences, filling, testing, valves, colour, transport and storage
- IS 308:2024 explained what the Indian specification for dissolved acetylene actually limits, how it is tested, and what changed in the fourth revision
- IS 14814:2023, the Indian code of safety for acetylene properties, pressure limits, the copper ban, flameproof equipment, physiological effects and PPE
- IS 8471:2003 explained what the Indian Standard requires of an acetylene generator, from pressure class and water ratio to relief valves and the 2024 amendment
- Acetylene pipelines in India under IS 15190 Part 1 (up to 155 kPa) and Part 2 (155 to 2,550 kPa) classes, materials, sizing, arrestors and testing
- Acetylene pipelines the one number that governs everything
- Electrical equipment in acetylene areas why acetylene is Group IIC, what IS/IEC 60079-1 flameproofing means, and when to pressurise or remove equipment instead
- Hydrostatic stretch testing of gas cylinders to IS 5844:2014 what is measured, the permanent-expansion limits, and why DA cylinders are examined instead
Gas safety data (SDS explained)11
The hazards of each gas in plain terms, with links to the full safety data sheets.
Also: All safety data sheets
- How to read an industrial gas safety data sheet the 16 GHS sections and the five that matter most for a gas
- Oxygen safety data explained why an oxidiser that does not burn is the gas that starts fires
- Nitrogen safety and asphyxiation why the gas that makes up 78 % of air kills without any warning
- Argon safety data explained an inert gas 1.38 times heavier than air that collects where welders work
- Carbon dioxide safety data explained why CO₂ is a toxic gas that an oxygen meter will not catch
- Hydrogen safety data explained a 4 to 75 % flammable range, an invisible flame and the same 0.02 mJ spark as acetylene
- Why hydrogen leaks behave unlike any other gas, and what to do about it
- Helium safety data explained why the balloon gas that alters the voice is an asphyxiant and a cryogen
- Nitrous oxide safety data explained an oxidiser that can decompose on its own, and why medical and industrial grades are not the same product
- Oxygen enrichment and deficiency in the workplace the narrow band between 19.5 % and 23.5 % and how to stay inside it
- Inert gas confined-space entry the permit, the gas test, continuous monitoring, the standby person and a rescue that does not add victims
Gas properties and data8
What industrial gases are, how they behave, and the numbers for each: properties, flammability, critical points, conversions and purity grades.
- What are industrial gases? The four families, the five ways they are supplied, and the Indian standard for each
- Industrial gas properties table molar mass, boiling point, density, relative density, critical point and flammable range for 12 gases
- Which industrial gases are flammable, which are oxidisers and which are inert one table for 12 common gases
- Critical temperature and pressure of industrial gases why CO₂ and N₂O are liquid in the cylinder and oxygen, nitrogen and argon never are
- Permanent, liquefied and dissolved gases why an oxygen cylinder is sold by cubic metre, a CO₂ cylinder by kilogram and an acetylene cylinder by net weight
- Gas laws for cylinder users Boyle, Charles, Gay-Lussac, the compressibility factor Z, and what heat does to a full cylinder
- Nm³ to kg and back a conversion table for oxygen, nitrogen, argon, CO₂, hydrogen, helium, N₂O, acetylene, air and propane
- Gas purity grades explained what N2.5, 4.0, 5.0 and 6.0 mean, how ppm relates to per cent, and which grade each job needs
Liquid and cryogenic gases5
Liquid nitrogen, oxygen and argon, the containers that hold them, and liquid medical oxygen.
- Liquid nitrogen temperature, density, expansion ratio, hazards and safe handling of dewars
- Liquid oxygen (LOX) temperature, density, why it is blue and magnetic, and why it is dangerous
- Liquid argon temperature, density, boiling point, hazards and how industry uses it
- Cryogenic containers explained open dewars, liquid cylinders and VIE tanks, their relief devices and Indian rules
- Liquid medical oxygen (LMO) in India the supply chain from air separation plant to hospital bed, and how it compares with PSA
Cylinders, valves and regulators3
The hardware between the gas and the job, and what to do when it leaks.
- Gas cylinder valves and outlet connections in India the IS 3224 outlet for each gas, left-hand fuel threads, pin-index valves and valve protection
- Gas cylinder regulators by gas the right connection, delivery range and special features for acetylene, oxygen, LPG, argon, nitrogen and CO₂
- A leaking gas cylinder what to do first, what never to do, and how the response changes for flammable, oxidising, inert and toxic gases
Other gases: uses, grades and data23
Oxygen, nitrogen, argon, CO₂, hydrogen, helium and nitrous oxide.
- What is oxygen gas used for? Industrial, medical and process uses with the purity each one needs
- Oxygen technical data sheet physical properties, IS 309:2023 grades, cylinder data and liquid expansion
- Industrial oxygen and medical oxygen what actually differs
- What nitrogen is used for purging, blanketing, cutting and cooling
- Nitrogen technical data sheet physical properties, IS 1747:2023 grades, PSA versus cryogenic purity and dew point
- PSA nitrogen why purity, not flow, decides what a plant costs
- What is argon gas used for? TIG and MIG shielding, stainless steelmaking, lighting, laboratory and more
- Argon technical data sheet physical properties, IS 5760 status, purity grades and cylinder pressure
- What carbon dioxide is used for, and why it is sold by weight
- Carbon dioxide technical data sheet triple point, vapour pressure, IS 307:2024 grades, liquid CO₂ cylinders and dry ice
- What is hydrogen gas used for? Refineries, ammonia, metal annealing, generator cooling, food and the ways it is delivered
- What is helium gas used for? MRI magnets, leak detection, lifting, welding, diving and why every litre must be conserved
- Helium why it is scarce, where it cannot be replaced, and how to waste less
- What is nitrous oxide gas used for? Anaesthesia and analgesia, whipped-cream propellant, AAS oxidant, engines and which grade for which
- Nitrous oxide what it is used for, and what a buyer must have in place
- Calibration standards and welding mixtures not the same product
- Plant air, instrument air and breathing air knowing which class a duty needs
- How much gas is in a cylinder? Water capacity, filling pressure and the arithmetic for every industrial gas in India
- What industrial gas costs in India, and the six things that move the price
- Hydrogen technical data formula H₂, density, boiling point, LEL and UEL, and why a gas has no flash point
- Helium technical data density, boiling point, compressibility, purity grades and the gas in balloons
- Nitrous oxide technical data vapour pressure, critical point, densities, decomposition and the medical and industrial grades
- What is nitrous oxide? The chemical name, the formula N₂O, why it is called laughing gas, and how it is used and controlled
On-site generation and pipelines8
Making your own gas, and the pipework that carries it.
- Cylinder supply or on-site generation how to decide honestly
- How a PSA oxygen plant makes oxygen out of air
- Designing an industrial gas pipeline sizing, materials and safety
- Medical gas pipeline systems what a hospital must have in place
- Cleaning a pipeline for oxygen service, and why it matters so much
- How oxygen is made cryogenic air separation, PSA, and how the gas gets into a cylinder to IS 309
- PSA, VPSA or cryogenic air separation choosing an oxygen gas plant by purity, scale, liquid output and energy
- Types of industrial gas plants how acetylene, PSA, air separation, CO₂, nitrous oxide and hydrogen plants work, and what each contains
History4
Where dissolved acetylene came from, and India's place in the story.
- How the dissolved acetylene cylinder was invented from Willson's carbide in 1892 and the explosions of 1896 to Janet's porous mass and acetone in 1901
- A short history of acetylene in India from imported carbide in 1928 and no Indian carbide before 1952 to the standards and rules that govern the trade today
- Is acetylene obsolete? The chemical industry left carbide in the 1960s welding, cutting and heating kept it, for reasons of flame physics
- Acetylene supply across the North-East what the geography does to it
No guide matches that. Try a shorter word, or ask KIGL — every guide here started as a question somebody could not find an answer to.